Aruba无线控制器常用 *** 作

Aruba无线控制器常用 *** 作,第1张

Aruba无线控制器常用 *** 作

初始配置

1.console到初始化的无线控制器上

Enter System name [Aruba7005]:
Enter VLAN 1 interface IP address [172.16.0.254]: 192.168.0.123
(输入内网没用的 IP ,这里为假设)
Enter VLAN 1 interface subnet mask [255.255.255.0]:
Enter IP Default gateway [none]:
Enter Switch Role, (master|local) [master]:
(在只有一台控制器的情况下一般我们把主控制器设为主)
Enter Country code (ISO-3166), <ctrl-I> for supported list: cn
( c代n表 中国)
You have chosen Country code CN for China (yes|no)?: y
Enter Time Zone [PST-8:0]:
Enter Time in GMT [02:31:57]:
Enter Date (MM/DD/YYYY) [4/11/2010]:
Enter Password for admin login (up to 32 chars): *****
(设置 admin 的密码)
Re-type Password for admin login: *****
Enter Password for enable mode (up to 15 chars): *****
(设置 enable 模式下的密码)
Re-type Password for enable mode: *****
Do you wish to shutdown all the ports (yes|no)? [no]:
Current choices are:
System name: Aruba200
VLAN 1 interface IP address: 192.168.0.123
VLAN 1 interface subnet mask: 255.255.255.0
IP Default gateway: none
Switch Role: master
Country code: cn
Time Zone: PST-8:0
Ports shutdown: no
If you accept the changes the switch will restart!
Type <ctrl-P> to go back and change answer for any question
Do you wish to accept the changes (yes|no)y
System restarted!

2.配置上联端口聚合

interface gigabitethernet 0/0/0
description "GE0/0/0"
trusted
trusted vlan 1-4094
lacp group 1 mode active interface gigabitethernet 0/0/1
description "GE0/0/1"
trusted
trusted vlan 1-4094
lacp group 1 mode active interface port-channel 1
trusted
trusted vlan 1-4094
switchport mode trunk
switchport access vlan 128
switchport trunk allowed vlan 1-63,71-4094

3..配置好以上的设置后, 我们就可以使用配置好的IP 地址, 在PC 端通过HTTPS 连接到控制器上进行配置。


新增SSID

1.新增VLAN

2.配置VLAN IP  (一般用作AC的管理IP)

interface vlan 49
ip address 10.11.49.251 255.255.255.0

3.创建AAA Profiles

此处保持默认即可

新建802.1X认证文件

Basic和Advanced两项里的内容保持默认即可。


4.配置Virtual AP

1)新建Virtual AP

2)新建SSID Profile

3)配置VLAN到Virtual AP

5.新建AP Group

6.激活AP

7.新增AP

1)AP上线后会显示在Controller的WIRELESS-AP Installation

2)将AP添加到对应组后点击下方Provision即可。


8.备份

1)每次修改配置后都Configuration 右侧会提示Save Configuration,点击保存到本地

2)点击备份

Copy 备份

欢迎分享,转载请注明来源:内存溢出

原文地址: https://outofmemory.cn/zaji/589501.html

(0)
打赏 微信扫一扫 微信扫一扫 支付宝扫一扫 支付宝扫一扫
上一篇 2022-04-12
下一篇 2022-04-12

发表评论

登录后才能评论

评论列表(0条)

保存