citrix服务器端如何配置啊？怎么设置服务器

1、 在浏览器中输入http://ServerName/Citrix/MetaFrameXP/wiadmin

2、 输入本机的管理员帐号名和密码，还有机器名（如果加入域，则可以使用域的帐号）

3、选择左侧栏中的Server-Side Firewall

把“Default address translation setting”项从Normal address 修改成Translated address

4、Specific address translation settings的 Client address prefix一项，输入也要访问这台CITRIX的内网IP地址的网段地址（例如：10.0.）然后点击ADD按钮，下面的框中会出现这个设置。可以输入多个网段。

5、MetaFrame server address translation map中，上面写内网的IP地址，外面写供外部访问的IP地址(用花生壳的填上的的域名)，写完以后点击ADD。

6、全部做完以后，点击最下面的SAVE按钮

7、点击新出来画面的APPLY CHANGES，再次点击APPLY CHANGES8、防火墙上设置NPT，转发80、1494端口。

Web Interface (WI) and NAT

Internal LAN

For instance you internal IP range is 192.168.x.x

With a default installation of the Web Interface (NFuse) it will work

for you LAN Clients. Of course, when connecting over the Internet, a

home User will NOT get any response from 192.168.x.x

Set the Public IP for the Citrix MetaFrame Servers

Whether residing on the DMZ, or the local LAN. Let's also say, the

Public IP is 123.123.123.1 On the Citrix Servers you need to run the

altaddr command, to tell the servers to respond with the Public address, if

needed.

On the command line run: altaddr /set 123.123.123.1

FireWall Settings for Citrix &Web Interface

Asuming Citrix MetaFrame/Web Interface are in the DMZ,

enable following rules:

- Allow TCP Port 1494 WAN to DMZ inbound (Citrix ICA)

- Allow high TCP Ports (1023 - 5000) outbound (Citrix ICA)

- Allow TCP Port 80 WAN to DMZ In- and outbound (HTTP)

(Check FW from outside with:

"Telnet 123.123.123.1 1494" and "Telnet 123.123.123.1 80")

Web Interface NAT Configuration

On the Web Interface Server either configure:

A: The alternative address use in the admin page

http:///Citrix/MetaFrameXP/WIAdmin/

Don't forget to SAVE and APPLY Settings

or

B: Make sure the two sample lines below are in the NFuse.conf

(needs an IIS reset if changed outside the WI admin page, run IISRESET

on the command line)

AlternateAddress=Mapped

ClientAddressMap=192.168.0.,Normal,*,Alternate

(Don't forget the last dot in the local IP range!)

After these changes, the template will get filled with the alternate

address for Internet users, and the internal address for your LAN

Clients.

Configuring NFuse 1.x for Use with Network Address Translation (NAT)

CTX584485

Back to the Index

你只要找到ICA的客户端安装程序就可以啦。不过安装之前客户端一定要加到域里面的。然后安装完毕，打开Start\All programs应该会看到一个ICA的图标，你可以将这个图标发送到桌面，一般新安装的程序，会特别凸显出来的，应该很容易找到的，一般客户端要求的都是win7的系统吧。这个时候你最好留个点（take snapshots）。不过如果你用的是2K8R2打了SP1的话，记得要在装客户端之前在server端安装HF01（是hotfix而不是HRP），不然无法launch session。然后打开ICA输入server的IP就好了。如果输入IP还是不行，记得检查server端的IMA，还有发布的站点是否由问题，防火墙是否关闭，license是否过期。还有可以在cmd中输入 qfarm /load 看看是否是0，如果是20000就要一直重启IMA了，最好是0。

---