如何在ARM7中进行AD转换

如何在ARM7中进行AD转换,第1张

主程序:/******************************************************************************/

/* This file is part of the uVision/ARM development tools */

/* Copyright KEIL ELEKTRONIK GmbH 2002-2004 */

/******************************************************************************/

/* */

/* BLINKY.C: LED Flasher */

/* */

/******************************************************************************/

#include /* LPC21xx definiTIons */

extern void init_serial (void); /* IniTIalize Serial Interface */

extern int putchar (int ch); /* Write character to Serial Port */

extern int getchar (void); /* Read character from Serial Port */

void puthex (int hex) { /* Write Hex Digit to Serial Port */

if (hex 》 9) putchar(‘A’ + (hex - 10));

else putchar(‘0’ + hex);

}

void putstr (char *p) { /* Write string */

while (*p) {

putchar (*p++);

}

}

void delay (void) { /* Delay funcTIon */

unsigned int cnt;

unsigned int val;

ADCR |= 0x01000000; /* Start A/D Conversion */

do {

val = ADDR; /* Read A/D Data Register */

} while ((val & 0x80000000) == 0); /* Wait for end of A/D Conversion */

ADCR &= ~0x01000000; /* Stop A/D Conversion */

val = (val 》》 6) & 0x03FF; /* Extract AIN0 Value */

putstr (“\nAIN0 Result = 0x”); /* Output A/D Conversion Result */

puthex((val 》》 8) & 0x0F); /* Write 1. Hex Digit */

puthex((val 》》 4) & 0x0F); /* Write 2. Hex Digit */

puthex (val & 0x0F); /* Write 3. Hex Digit */

val = (val 》》 2) 《《 12; /* Adjust Delay Value */

for (cnt = 0; cnt 《 val; cnt++); /* Delay */

}

int main (void) {

unsigned int n;

IODIR1 = 0x00FF0000; /* P1.16..23 defined as Outputs */

ADCR = 0x002E0401; /* Setup A/D: 10-bit AIN0 @ 3MHz */

init_serial(); /* IniTIalize Serial Interface */

IOSET1=0x00ff0000;

while (1) { /* Loop forever */

for (n = 0x00010000; n 《= 0x00800000; n 《《= 1) {

/* Blink LED 0, 1, 2, 3, 4, 5, 6, 7 */

IOCLR1 = n; /* Turn on LED */

delay(); /* Delay */

IOSET1 = 0x00FF0000; /* Turn off LEDs */

}

}

}

串口程序:

/******************************************************************************/

/* This file is part of the uVision/ARM development tools */

/* Copyright KEIL ELEKTRONIK GmbH 2002-2004 */

/******************************************************************************/

/* */

/* SERIAL.C: Low Level Serial Routines */

/* */

/******************************************************************************/

#include /* LPC21xx definitions */

#define CR 0x0D

void init_serial (void) { /* Initialize Serial Interface */

PINSEL0 = 0x00050000; /* Enable RxD1 and TxD1 */

U1LCR = 0x83; /* 8 bits, no Parity, 1 Stop bit */

U1DLL = 97; /* 9600 Baud Rate @ 15MHz VPB Clock */

U1LCR = 0x03; /* DLAB = 0 */

}

int putchar (int ch) { /* Write character to Serial Port */

if (ch == ‘\n’) {

while (!(U1LSR & 0x20));

U1THR = CR; /* output CR */

}

while (!(U1LSR & 0x20));

return (U1THR = ch);

}

int getchar (void) { /* Read character from Serial Port */

while (!(U1LSR & 0x01));

return (U1RBR);

}

欢迎分享,转载请注明来源:内存溢出

原文地址: http://outofmemory.cn/dianzi/2601554.html

(0)
打赏 微信扫一扫 微信扫一扫 支付宝扫一扫 支付宝扫一扫
上一篇 2022-08-09
下一篇 2022-08-09

发表评论

登录后才能评论

评论列表(0条)

保存