CAN总线控制器IP核代码分析

 

`include "TImescale.v"

// synopsys translate_on

`include "can_defines.v"

 

module can_top

(

  `ifdef CAN_WISHBONE_IF

    wb_clk_i,

    wb_rst_i,

    wb_dat_i,

    wb_dat_o,

    wb_cyc_i,

    wb_stb_i,

    wb_we_i,

    wb_adr_i,

    wb_ack_o,

  `else

    rst_i,

    ale_i,

    rd_i,

    wr_i,

    port_0_io,

  `endif

  cs_can_i,

  clk_i,

  rx_i,

  tx_o,

  irq_on,

  clkout_o

);

 

parameter Tp = 1;

 

`ifdef CAN_WISHBONE_IF

  input        wb_clk_i;

  input        wb_rst_i;

  input  [7:0] wb_dat_i;

  output [7:0] wb_dat_o;

  input        wb_cyc_i;

  input        wb_stb_i;

  input        wb_we_i;

  input  [7:0] wb_adr_i;

  output       wb_ack_o;

 

  reg          wb_ack_o;

  reg          cs_sync1;

  reg          cs_sync2;

  reg          cs_sync3;

 

  reg          cs_ack1;

  reg          cs_ack2;

  reg          cs_ack3;

  reg          cs_sync_rst1;

  reg          cs_sync_rst2;

`else

  input        rst_i;

  input        ale_i;

  input        rd_i;

  input        wr_i;

  inout  [7:0] port_0_io;

 

  reg    [7:0] addr_latched;

  reg          wr_i_q;

  reg          rd_i_q;

`endif

 

input        cs_can_i;

input        clk_i;

input        rx_i;

output       tx_o;

output       irq_on;

output       clkout_o;

 

reg          data_out_fifo_selected;

 

 

wire         irq_o;

wire   [7:0] data_out_fifo;

wire   [7:0] data_out_regs;

 

 

/* Mode register */

wire         reset_mode;

wire         listen_only_mode;

wire         acceptance_filter_mode;

wire         self_test_mode;

 

/* Command register */

wire         release_buffer;

wire         tx_request;

wire         abort_tx;

wire         self_rx_request;

wire         single_shot_transmission;

 

/* ArbitraTIon Lost Capture Register */

wire         read_arbitraTIon_lost_capture_reg;

 

/* Error Code Capture Register */

wire         read_error_code_capture_reg;

wire   [7:0] error_capture_code;

 

/* Bus TIming 0 register */

wire   [5:0] baud_r_presc;

wire   [1:0] sync_jump_width;

 

/* Bus Timing 1 register */

wire   [3:0] time_segment1;

wire   [2:0] time_segment2;

wire         triple_sampling;

 

/* Error Warning Limit register */

wire   [7:0] error_warning_limit;

 

/* Rx Error Counter register */

wire         we_rx_err_cnt;

 

/* Tx Error Counter register */

wire         we_tx_err_cnt;

 

/* Clock Divider register */

wire         extended_mode;

 

/* This section is for BASIC and EXTENDED mode */

/* Acceptance code register */

wire   [7:0] acceptance_code_0;

 

/* Acceptance mask register */

wire   [7:0] acceptance_mask_0;

/* End: This section is for BASIC and EXTENDED mode */

 

 

/* This section is for EXTENDED mode */

/* Acceptance code register */

wire   [7:0] acceptance_code_1;

wire   [7:0] acceptance_code_2;

wire   [7:0] acceptance_code_3;

 

/* Acceptance mask register */

wire   [7:0] acceptance_mask_1;

wire   [7:0] acceptance_mask_2;

wire   [7:0] acceptance_mask_3;

/* End: This section is for EXTENDED mode */

 

/* Tx data registers. Holding identifier (basic mode), tx frame information (extended mode) and data */

wire   [7:0] tx_data_0;

wire   [7:0] tx_data_1;

wire   [7:0] tx_data_2;

wire   [7:0] tx_data_3;

wire   [7:0] tx_data_4;

wire   [7:0] tx_data_5;

wire   [7:0] tx_data_6;

wire   [7:0] tx_data_7;

wire   [7:0] tx_data_8;

wire   [7:0] tx_data_9;

wire   [7:0] tx_data_10;

wire   [7:0] tx_data_11;

wire   [7:0] tx_data_12;

/* End: Tx data registers */