华为pppoe配置实战演练

概述一、 配置pppoe服务器 1.将AR2配置为pppoe服务器 <Huawei> sysEnter system view, return user view with Ctrl+Z.[Huawei]sysn SERVER[SERVER]ip pool pool1 //配置一个地址池pool1Info: It‘s successful to create an IP addre

一、 配置pppoe服务器 1.将AR2配置为pppoe服务器

<Huawei> sysEnter system vIEw,return user vIEw with Ctrl+Z.[Huawei]sysn  SERVER[SERVER]ip pool pool1      //配置一个地址池pool1Info: It‘s successful to create an IP address pool.[SERVER-ip-pool-pool1]network  10.1.12.0  mask 255.255.255.0[SERVER-ip-pool-pool1]gateway-List 10.1.12.254[SERVER-ip-pool-pool1]quit[SERVER]interface Virtual-Template 1    //配置一个虚拟接口Jul 29 2018 23:44:49-08:00 SERVER %%01IFPDT/4/IF_STATE(l)[0]:Interface Virtual-Template1 has turned into UP state.[SERVER-Virtual-Template1]ppp authentication-mode chap    //配置认证模式为chap[SERVER-Virtual-Template1]ip add 10.1.12.254 24[SERVER-Virtual-Template1]remote address pool pool1          //分配ip地址[SERVER-Virtual-Template1]quit

2.在AR2上的g0/0/0接口绑定虚拟模板

[SERVER]int g0/0/0[SERVER-GigabitEthernet0/0/0]pppoe-server bind virtual-template 1  //绑定virtual-template 1[SERVER-GigabitEthernet0/0/0]quit

3.为pppoE被认证方创建账户和密码

[SERVER]aaa[SERVER-aaa]local-user zh password cipher huawei    Info: Add a new user.[SERVER-aaa]local-user zh service-type ppp[SERVER-aaa]quit

二、配置pppoe客户端 4.将AR1配置为pppoe客户端

<Huawei>sysEnter system vIEw,return user vIEw with Ctrl+Z.[Huawei]sysname AR1[AR1]dialer-rule             //进入dialer-rule视图[AR1-dialer-rule]dialer-rule 1 ip permit     //允许ip流量触发拨号[AR1-dialer-rule]quit[AR1]interface dialer 1                 //创建并进入dialer 1接口[AR1-Dialer1]Jul 29 2018 23:47:33-08:00 AR1 %%01IFPDT/4/IF_STATE(l)[0]:Interface Dialer1 has turned into UP state.[AR1-Dialer1]dialer user zh          //配置用户对端用户名，这个用户名需与服务器端的ppp用户名相同[AR1-Dialer1]dialer-group 1         //将接口置于一个拨号访问组[AR1-Dialer1]dialer bundle 1      [AR1-Dialer1]ppp chap user zh      //指定dialer 1 接口的编号（用于和物理接口绑定）[AR1-Dialer1]ppp chap password  cipher huawei[AR1-Dialer1]dialer timer IDle 300        //设置按需pppoe拨号的空闲时间（300s没有流量就断开）INFO:  The configuration will become effective after link reset.[AR1-Dialer1]ip address ppp-negotiate    //ip地址协商

5.将pppoe拨号接口绑定到出接口

[AR1-Dialer1]interface g0/0/0[AR1-GigabitEthernet0/0/0]pppoe-clIEnt dial-bundle-number 1  [AR1-GigabitEthernet0/0/0]quit

6.配置本端到服务器的缺省静态路由

[AR1]ip route-static 0.0.0.0 0.0.0.0 Dialer 1

三、验证 7.在SERVER上执行display pppoe-server session all和display virtual-access命令，查看PPPoE会话的状态和配置信息。

8.查看AR1上的拨号接口的信息，并确认拨号接口能够从PPPoE服务器获得IP地址。

<AR1>display ip interface brIEf

总结

以上是内存溢出为你收集整理的华为pppoe配置实战演练全部内容，希望文章能够帮你解决华为pppoe配置实战演练所遇到的程序开发问题。

如果觉得内存溢出网站内容还不错，欢迎将内存溢出网站推荐给程序员好友。